Nie mogę zainstalować systemu na moim komputerze!?

28.11.03, 11:58
Mam poważny problem. Posiadam dwa dyski: Seagate 20 Gb i WD Cawiar 80 Gb. Na
Cawiarku 3x strociłem partycje systemową, w tym momencie nie jestem w stanie
zainstalować na nim żadnego systemu jeśli pracuje w moim komputerze (kiedy
wkładałem go do dwóch innych kompów istalacja przebiegała bezproblemowo). Na
Seagate wszystko jest ok. Czym to może być spowodowane? Dysk ten mam od pół
roku i do tej pory sprawował się bez zarzutu.
    • Gość: piecyk gazowy Re: Nie mogę zainstalować systemu na moim kompute IP: *.internetdsl.tpnet.pl 28.11.03, 12:26
      Może włączona ochrona antywirusowa w BIOS-ie?
      • milu100 Re: Nie mogę zainstalować systemu na moim kompute 28.11.03, 13:07
        Niestety ochrona antywirusowa jest wyłączona. System nie chce mi się
        zainstalować tylko na tym dysku, mimo, że na innych kompach nie miał tego
        problemu.
        • Gość: piecyk gazowy Re: Nie mogę zainstalować systemu na moim kompute IP: *.internetdsl.tpnet.pl 28.11.03, 13:23
          A jak to wygląda, że nie chce się zainstalować?
          • milu100 Re: Nie mogę zainstalować systemu na moim kompute 28.11.03, 13:30
            Instalacja rozpoczyna się normalnie, niebieski ekran itd, a potem się wiesz:
            najczęściej przy zatwierdzaniu licenji, lub przy wyborze partycji.
    • Gość: Adam Re: Nie mogę zainstalować systemu na moim kompute IP: 195.117.250.* 29.11.03, 15:34
      Pyt: 1. bios poprawnie wykrywa dysk?
      2. Czy po podłączeniu do innego kompa widzisz partycje na dysku 80gb?
      3. Jaki system miałeś zainstalowany wcześniej
      4. Czy masz zainstalowany jakikolwiek systemw chwili obecnej i czy zależy
      ci na danych?

      Generalnie podałeś mało danych do wnioskowania:ale...
      1.Może być tak ze maszw biosie botowanie ustawione na jedynie pierwszy dysk
      2. Może być uszkodzony sektor mbr albo też mogą być w nim śmieci
      w takim przypadku fdisk/mbr
      to tyle co mi teraz przychodzi do głowy
      • Gość: mgregor Re: Nie mogę zainstalować systemu na moim kompute IP: *.neoplus.adsl.tpnet.pl 30.11.03, 13:38
        Ja moge ew. polecic program ze strony Western Digitala (o ile sie nie myle to
        pod jego skrzydlami w tej chwili produkowane sa dyski Caviar) do testowania i
        czyszczenia (w programie jest opcja zapisu calego dysku zerami) dyskow.
        Ostatnio udalo mi sie nim ozywic dysk ktorego formatowanie zatrzymywalo sie na
        54% (we wszystkich systemach). Ale jak nie chce Ci sie go sciagac to pomysl
        Adama tez moze pomoc...

        Pozdrawiam serdecznie
        mgregor
        • Gość: Lupus Re: Nie mogę zainstalować systemu na moim kompute IP: *.cpe.net.cable.rogers.com 30.11.03, 16:08
          Usun wszystkie partycje i stworz nowa albo instaluj na niesformatowany disk
          jesli wiesz jak to zrobic.
      • Gość: milu100 Re: Nie mogę zainstalować systemu na moim kompute IP: *.internetdsl.tpnet.pl 30.11.03, 16:06
        1. tak, jest wykrywany
        2. na innych kompach wszystko jest ok, system instaluje się porawnie
        3. WinXP
        4. dane są nieważne

        Foramatowałem go na innym komputerze i zastanawia mnie jedna rzecz:
        PartitionMagic nie chciał się uruchomić tylko pokazywał błąd:
        Error 100: partition table is bad

        stosowałem już fdisk /mbr
        i tu też pyatanie czy po użuyciu tego polecenia powinien pojawić się jakiś
        komunikat? Bo u mnie nic się nie pojawiło oprócz nowego znaku zachęty

        pozdr
        • Gość: Lupus Re: Nie mogę zainstalować systemu na moim kompute IP: *.cpe.net.cable.rogers.com 30.11.03, 16:12
          Uzyj wiec P Magic i usun (delete) cala partycje.Stworz nowa jako
          primary ,sformatuj caly czas uzywajac PMagic i instaluj.
          • Gość: milu100 Re: Nie mogę zainstalować systemu na moim kompute IP: *.internetdsl.tpnet.pl 30.11.03, 16:32
            > Uzyj wiec P Magic i usun (delete) cala partycje.Stworz nowa jako
            > primary ,sformatuj caly czas uzywajac PMagic i instaluj.


            Chciałbym to zrobić, ale jak juz napisałem PM mi się nie chce uruchomic z
            powodu error 100, i to zarówno w wersji 6 jak i 8.

            Dysk partycjonowałem już od nowa pod fdiskiem, ale cały czas partitionMagic
            twierdzi, że partition table i bad i odmawia współpracy.

            A Norton Disk Doctor nie widzi na dysku żadnych błędów.

            • Gość: Lupus Re: milu100 IP: *.cpe.net.cable.rogers.com 30.11.03, 17:26
              Duzo czytania ale mysle ze dasz sobie rade:

              Solution: Error 100 Partition Table Is Bad


              Cause 1: This error usually results if either of the following rules is
              violated: 1) the master boot record (MBR) can contain, at most, one logical
              drive entry; and 2) each Extended Partition Boot Record (EPBR) can contain, at
              most, one link to another EPBR. If either of these rules is violated, the
              PowerQuest product reports an error and is prevented from recognizing any of
              the hard disk's partitions, since data could be lost if the PowerQuest product
              were to make any modifications to partitions in this situation.


              Fix 1: In some cases, the PARTINFO utility can be used to correct the problems
              that are causing Error 100.

              NOTE: Before performing the following steps, please run a PARTINFO, saving the
              output as a .TXT file on a floppy (see PowerQuest Solution 62 for more
              information). This captures important information about the current state of
              your hard drive before any further changes are made to it. If you need more
              help in correcting Error 100, a PowerQuest technician may request this
              PARTINFO output.

              1. Run PARTINFO with the /EPC switch to determine if there is a problem with
              logical drive entries in your MBR or EPBR(s).

              2. If any problems are found, run PARTINFO with the /EPF switch to try to
              correct the errors.

              3. If PARTINFO is unable to fix the problems, you must create new, error-free
              partition tables.

              -------------------------------------------------------------------------------
              ---------------------------------------------------------

              Cause 2: Error 100 can be caused if the PowerQuest product mistakenly
              identifies removable drives as fixed drives.


              Fix 2: To work around this issue, try any of the following:

              - Go into the BIOS Setup and change the device settings for the removable
              device (or devices) from "Auto" to "None."
              - If you have a Zip drive, insert a Zip disk in the drive, or remove the drive
              from the system while you are using your PowerQuest product.
              - If you have a notebook with a memory card that is assigned a drive letter,
              remove the card while you are using your PowerQuest product.

              -------------------------------------------------------------------------------
              ---------------------------------------------------------

              Cause 3: On systems with an HP370 RAID controller, if you install HighPoint
              drivers during the installation of Windows XP, Windows will revert back to
              it's own RAID controller driver.


              Fix 3: After you have finished installing Windows XP, install the latest
              HighPoint drivers. (For more information on controller driver issues with
              Windows XP, see Article IDs Q225125 and Q220845 on Microsoft's online
              Knowledge Base.

              -------------------------------------------------------------------------------
              ---------------------------------------------------------

              Cause 4: On some Windows XP machines, the operating system installs a SCSI
              driver even if no physical SCSI drive is present.


              Fix 4: In the Device Manager, remove any SCSI drives listed there that do not
              actually exist in your system.

              -------------------------------------------------------------------------------
              ---------------------------------------------------------

              Cause 5: An HP p1000 photo printer with an MMC slot is attached to the
              computer, causing the computer to detect the printer as a fixed drive.


              Fix 5: Unplug the HP p1000 photo printer from your computer while you are
              using your PowerQuest program.

              --------------------------------------------------------.
              -------------------------------------------------------------------------------
              -

              Cause 6: On systems with an HP Photosmart 1215 printer with a built-in memory
              card reader, Windows XP detects the card reader as a removable disk. (It shows
              up in Windows Explorer as the D: drive.)


              Fix 6: Remove the HP Photosmart 1215 printer from Windows Device Manger,
              unplug the printer's parallel cable from the PC, reboot the computer, and then
              use your PowerQuest program.

              -------------------------------------------------------------------------------
              ---------------------------------------------------------

              Other things to try:
    • Gość: ppp Re: Nie mogę zainstalować systemu na moim kompute IP: 213.25.130.* 30.11.03, 16:15
Pełna wersja